Seismic Applications

Many innovative advances in the seismic method have been introduced over recent years. In this discussion, I will focus on the topic of sampling. A key example is the azimuthal sampling in full-azimuth 3D surveys—surveys that are needed, for instance, to characterize fractures. Full-azimuth geometries typically call for an expensive explosion in the amount of data needing to be acquired. A way to reduce the acquisition cost is to rely instead on interpolation, but aliasing issues limit the spatial frequencies that can be recovered.

In the marine world, an innovation to address this has been to collect crossline-oriented, particle-acceleration measurements in addition to the usual pressure measurements (made by hydrophones). Particle acceleration is related directly to the spatial gradient of the pressure. Knowing both the pressure and the pressure derivative extends the ability for successful interpolation. Another innovation in use today is to abandon the traditional inline/crossline field geometry by shooting in circular tracks instead. Regardless of whether straight lines or circular tracks are used, platforms and other obstructions block access to towed streamers. Placing receiver nodes on the seabed is a very popular way around this problem when corals are not present. Otherwise, wave- and solar-powered unmanned surface vehicles provide a new, tantalizing alternative innovation. Each of these bathtub-sized crafts independently tows a hydrophone array.

In the onshore world, one of the big advances for addressing increased sampling requirements has been to go to 24-hour shooting with continuous recording of simultaneously sweeping vibrators. This has been enabled by innovations in both acquisition and processing. In acquisition, the introduction of vibrator command-and-control systems means that the vibrator drivers no longer must wait for the start signal from the recording truck. In processing, the development of deblending algorithms enables the overlapping field records to be separated. These advances dramatically increase the number of records that can be acquired each day—especially in desert regions. An innovation for improving this efficiency even further is to skip over some of the source and receiver positions in a carefully specified, random-looking fashion adopted from the science of compressive sampling. (By relying on sparsity in an appropriate transform domain, data processing can reconstruct the seismic signal adequately from the reduced data set.)

Finally, yet another form of sampling of interest today is the time interval between consecutive monitor surveys in 4D programs. Recent innovations enable frequent, lower-cost monitor surveys to see small, rapid changes in deepwater reservoirs.

For more information, see the featured papers.

This Month's Technical Papers

Acquisition With Autonomous Marine Vehicles: Field Test

Advances in 4D Seismic and Geophysical Monitoring of Deepwater Fields

Unconventional-Reservoir Characterization With Azimuthal Seismic Diffraction Imaging

Recommended Additional Reading

SPE 187203 Look-Ahead Geosteering By Means of Real-Time Integration of Logging-While-Drilling Measurements With Surface Seismic by F. Arata, Eni, et al.

SPE 184029 Seismic Airborne TEM Joint Inversion and Surface Consistent Refraction Analysis: New Technologies for Complex Near-Surface Corrections by Daniele Colombo, Saudi Aramco, et al.

URTeC 2670158 The Use of Time-Lapse Seismic Attributes for Characterizing Hydraulic Fractures in a Tight Siltstone Reservoir by N. Riazi, University of Calgary, et al.

Mark S. Egan, SPE, is a consulting geophysicist. He worked for Schlumberger and its heritage companies from 1975 to 2016, at which time he retired. Egan’s last position at Schlumberger was as global chief area geophysicist in the Land Unconventionals Group within the WesternGeco segment. His previous postings included chief geophysicist positions in North America, Saudi Arabia, Dubai, and London. Egan holds a PhD degree in ­geophysics, an MS degree in acoustics, and a BS degree in ­physics and mathematics. He is a member of SPE, the Society of Exploration Geophysicists, the European Association of Geoscientists and Engineers, and various local societies. Egan is a member of the JPT Editorial Committee and can be reached at

Seismic Applications

Mark S. Egan, SPE, Consulting Geophysicist

01 March 2018

Volume: 70 | Issue: 3

No editorial available



Don't miss out on the latest technology delivered to your email weekly.  Sign up for the JPT newsletter.  If you are not logged in, you will receive a confirmation email that you will need to click on to confirm you want to receive the newsletter.